FOR REFERENCE ONLY
This model has been discontinued
Thorowgood
T4 Pony Long Leg
Colour: Black
Changeable Gullet: N/M to XXW
Gullet Bar Type: S-Bar
This all-round saddle helps the young rider develop a balanced and independent seat. Super-comfy and stylish, with slimline panels to allow clear communication of the leg aids
Ideal for all kinds of riding activities!
It is available in 4 seat sizes, scaled to accommodate the very young child on their first pony, through to the more active teenager or petite adult rider.
Luxurious suede-effect seat covering and knee pads are non-slip and really comfortable to ride on.
The panels are flocked with 100% British wool and have a maximised bearing surface, while the short panel design enables this saddle to fit on short-backed ponies. This saddle is available in one panel profile (standard) but thanks to the SimaTree S-Bar can be adjusted to suit low wither and standard wither fits.
A longer flap option is in the 16" and 16½" models to accommodate the rider with a longer leg.
Changeable Gullet
Easily change the gullet bar to best fit the width of the horse’s withers
Gullet Bar Widths
NB: There are two gullet bar lengths (R and S type) to suit the specific tree designs. *XXW (Silver) size is available in S-Bar only.
Step 1: Use the hex key to remove the 2 screws at the front of each panel.
Step 2: Slide the panel off the point of the tree.
Step 3: Unscrew all four bolts in the gullet bar and remove the gullet bar.
Step 4: Insert different width of gullet bar. Insert all four bolts by hand then secure. Use the indent in the tree to position the bar facing the right way.
Only SimaTree gullet bars are suitable for Thorowgood saddles. You must NOT use any other bar in your Thorowgood saddle.
The S-Bar and R-Bars are not interchangeable. You must use the correct bar for your saddle model.
Multiple Girthing Options
GP models are fitted with three girth straps. The point (front) strap and second strap are stitched, the third strap is moveable. This changeable girthing arrangement allows saddle stability to be optimised instantly.
Begin by girthing in the neutral position using the second and third billet. (NOTE: This is the same as girthing on the first and third billets on a saddle with a conventional girthing system)
If you find the saddle slips forward, you can use straps 1 and 3
If the back of the saddle lifts away from the horse’s back, move the third strap onto the floating balance position and use straps 2 and 4
For increased stability you can use straps 1 and 4
NEVER girth using positions 1 & 2. This causes saddle instability and potential discomfort for your horse.
Changeable Girth Straps
The moveable girth strap can be positioned on the back ring to achieve optimal saddle stability
Step 1: Feed the strap through the ring with the point upwards and the top side of the strap facing down against the sweat flap.
Step 2: Curl the strap round and through the webbing loop
Step 3: Pull the strap tight ensuring the webbing loop lies flat against the top of the strap. (Reverse the above steps to remove a girth strap).
- Wipe down any smooth sections with warm water and a cloth. If it's really dirty, a mild detergent can be used.
- Use a soft bristled brush (such as a body brush) to remove dirt from the seat and knee rolls
- Avoid products that are glycerine or oil based, or those that contain alcohol (such as spray cleaners)
- Wipe down the non-leather sections (flap and panels) with warm water and a cloth. A mild detergent can be used to remove stubborn dirt. Remember to clean all surfaces. These areas require no further products or conditioners.
- If your saddle has leather stirrup straps, take care NOT to apply saddle soap or conditioner to the surface which comes into contact with the saddle flap.
- DON'T use a suede brush. The wire bristles are too course for the T4 saddle material and could cause damage.
-
Always allow your saddle to dry naturally. Do not use external heat sources and don't put it on a radiator, or hot pipes.
