FOR REFERENCE ONLY
This model has been discontinued
Thorowgood
T4 Compact GP
Colour: Black
Changeable Gullet: N/M to XW/XXW
Gullet Bar Type: R-Bar
This saddle has a slightly flatter tree on the underside and compact, slimline panels that allow the rider to feel closer to the horse. Although the seat is true to size, it offers a different feel to our Original GP and petite riders or those with narrower hips may feel it suits them better.
This saddle is ideal for croup high or flat backed horses, as well as standard fits.
Super-comfy deeper seat that gives you a little extra in-saddle security and locates you centrally for balance and control.
Versatile GP that’s forward enough cut to allow for jumping and cross-country as well as schooling and hacking.
Fully adjustable knee and calf blocks provide customised leg support.
Luxurious suede-effect seat covering and knee pads are non-slip and really comfortable to ride on.
Flocked with 100% British wool.
Changeable Gullet
Easily change the gullet bar to best fit the width of the horse’s withers
Gullet Bar Widths
NB: There are two gullet bar lengths (R and S type) to suit the specific tree designs. *XXW (Silver) size is available in S-Bar only.
Step 1: Use the hex key to remove the 2 screws at the front of each panel.
Step 2: Slide the panel off the point of the tree.
Step 3: Unscrew all four bolts in the gullet bar and remove the gullet bar.
Step 4: Insert different width of gullet bar. Insert all four bolts by hand then secure. Use the indent in the tree to position the bar facing the right way.
Only SimaTree gullet bars are suitable for Thorowgood saddles. You must NOT use any other bar in your Thorowgood saddle.
The S-Bar and R-Bars are not interchangeable. You must use the correct bar for your saddle model.
Multiple Girthing Options
GP models are fitted with three girth straps. The point (front) strap and second strap are stitched, the third strap is moveable. This changeable girthing arrangement allows saddle stability to be optimised instantly.
Begin by girthing in the neutral position using the second and third billet. (NOTE: This is the same as girthing on the first and third billets on a saddle with a conventional girthing system)
If you find the saddle slips forward, you can use straps 1 and 3
If the back of the saddle lifts away from the horse’s back, move the third strap onto the floating balance position and use straps 2 and 4
For increased stability you can use straps 1 and 4
NEVER girth using positions 1 & 2. This causes saddle instability and potential discomfort for your horse.
Changeable Girth Straps
The moveable girth strap can be positioned on the back ring to achieve optimal saddle stability
Step 1: Feed the strap through the ring with the point upwards and the top side of the strap facing down against the sweat flap.
Step 2: Curl the strap round and through the webbing loop
Step 3: Pull the strap tight ensuring the webbing loop lies flat against the top of the strap. (Reverse the above steps to remove a girth strap).
- Wipe down any smooth sections with warm water and a cloth. If it's really dirty, a mild detergent can be used.
- Use a soft bristled brush (such as a body brush) to remove dirt from the seat and knee rolls
- Avoid products that are glycerine or oil based, or those that contain alcohol (such as spray cleaners)
- Wipe down the non-leather sections (flap and panels) with warm water and a cloth. A mild detergent can be used to remove stubborn dirt. Remember to clean all surfaces. These areas require no further products or conditioners.
- If your saddle has leather stirrup straps, take care NOT to apply saddle soap or conditioner to the surface which comes into contact with the saddle flap.
- DON'T use a suede brush. The wire bristles are too course for the T4 saddle material and could cause damage.
-
Always allow your saddle to dry naturally. Do not use external heat sources and don't put it on a radiator, or hot pipes.
